我可以: 邀请好友来看>>
ZOL星空(中国) > 硬件星空(中国) > 显卡星空(中国) > 显卡BIOS讨论星空(中国) > 无法刷4850BIOS
帖子很冷清,卤煮很失落!求安慰
返回列表
签到
手机签到经验翻倍!
快来扫一扫!

无法刷4850BIOS

330浏览 / 6回复

laoda6175

laoda6175

0
精华
11
帖子

等  级:Lv.3
经  验:1232
  • Z金豆: 2

    千万礼品等你来兑哦~快点击这里兑换吧~

  • 城  市:安徽
  • 注  册:2009-02-25
  • 登  录:2025-03-10
发表于 2010-06-17 01:49:30
电梯直达 确定
楼主

ATIFLASH
========
Error list and troubleshooting guide.


0FL01?Error programming ROM
----------------------------
- Check that the command line arguments you passed are correct.
- Check that the BIOS image file specified exists and isn't corrupted.
- Check that the ROM isn't write protected.
- If a parameter in the BIOS image file differs from a parameter in the
  current ROM image (e.g. SSID), and you're sure you want to program
  the image, specify the -f (force) flag on the command line.


0FL02?Error accessing ROM
--------------------------
- Check that the command line arguments you passed are correct.
- Check that the ROM connections on the board are secure.


0FL03?Error in checksum
------------------------
For a BIOS image file:
- Check that the checksum you specified on the command line is correct.
- Check if your BIOS file has been corrupted.

For the board BIOS:
- Check that the checksum you specified on the command line is correct.
- Try programming the BIOS again.

For the board ROM:
- Check that the checksum you specified on the command line is correct.
- Check that the size you specified on the command line is correct.
- Verify that the extra non-BIOS contents of the ROM are correct.
- Try programming the BIOS again.


0FL04?Error verifying ROM
--------------------------
- Check that the command line arguments you passed are correct.
- Check that the BIOS image file specified exists and isn't corrupted.
- Check that the BIOS programmed into the ROM is the same as the one
  specified on the command line.
- Try reprogramming the ROM with the BIOS image.


0FL05?Error modifying SSID / BIOS
---------------------------
- If using -mi check that the command line arguments you passed are correct.
- If using -mb check that the contents of file you passed are correct.
- Test the rom access (atiflash -t ).
- Check that the ROM isn't write protected.
- Check that the BIOS programmed into the ROM isn't corrupted.
- Try reprogramming the ROM, then modifying the SSID again.

无法刷4850的BIOS,DOS下刷的,出现了以上的错误,求强人解答

gongzi600

gongzi600


精华

帖子

等  级:Lv.3
经  验:947
发表于 2010-06-17 09:03:18 1楼
rom文件不对应吧 你换个版本的软件试试

gongzi600

gongzi600


精华

帖子

等  级:Lv.3
经  验:947
发表于 2010-06-17 09:04:18 2楼
- Test the rom access (atiflash -t ).
检查rom是否正常的命令

gongzi600

gongzi600


精华

帖子

等  级:Lv.3
经  验:947
发表于 2010-06-17 09:04:48 3楼
- Check that the ROM isn't write protected.
检查你的rom是否有写保护

laoda6175

laoda6175


精华

帖子

等  级:Lv.3
经  验:1232
发表于 2010-06-17 16:42:59 4楼
我用的强刷,就是刷不了,真郁闷,我这个4830应该是可以刷的吧

txy1108

txy1108


精华

帖子

等  级:Lv.3
经  验:741
发表于 2010-07-27 22:02:26 5楼
在纯DOS下,使用命令 atiflash -p -f 0 xxxx 即可刷新,xxxx为BIOS档名

jiulushi

jiulushi


精华

帖子

等  级:Lv.1
经  验:203
发表于 2010-07-28 15:27:41 6楼
支持你哈
高级模式
星空(中国)精选大家都在看24小时热帖7天热帖大家都在问最新回答

针对ZOL星空(中国)您有任何使用问题和建议 您可以 联系星空(中国)管理员查看帮助  或  给我提意见

快捷回复 APP下载 返回列表